Hi everyone, I bought 2 drones recently, both DJI phantom 2 vision pluses. One is great but the other one needed some work, the camera was not attached and the ribbon cable damaged. I have replaced the cable and attached the camera but when turning on, the camera goes crazy, and all the parts get very warm after a few seconds. I have watched loads of Youtube videos about this and followed
The upgraded DJI remote control unit. The most dramatic change you will see when using the upgraded version has to do with the remote control. It comes with new features, including a gimbal control dial, built-in and rechargeable LiPo battery, and battery level LED indicators. The new TX is compatible with the Phantom 2 Vision+, Phantom 2
This is how I turn on my Phantom: 1.Turn on controller 2.Turn on range extender 3.Turn on Phantom 4.Calibrate Phantom This is what I do to start flying: 1.I connect my iPhone with WiFi to "Phantom" network. 2.I can receive live camera feed on iPhone so everything is good and working fine, all signals and calibration are good. First ,on phone u need to enable USB debugging and then enable PTP mode after connecting phone to PC, then run .exe of helium on PC, that is it. ( koush/support-wiki) Then just select litchi in helium, and backup. Phantom 2 Phantom vision 2 camera not working. Bellenie 2020-11-22 Views (3.9K) Phantom 2 DJI Phantom 2 will not connect Drone Repair Shop will not work on it. Once the extender is reset connect to the phantom_XXXX wifi and then open the Dji app go into settings and bindings and choose new camera and enter the MAC address you obtained earlier. Click the top blue button and exit settings and close the app. Now wait, the range extender will reset itself. No video or camera control on Phantom 4 Pro. 2#. My Phantom 4 Pro has been having video signal problems for the past month. It started with flickering and time lag, and now the video only shows static snow. This is happening in many different places, and I’m sure the most recent ones were free from any radio signal interference.
Credits: Tips 2 Fix. Open the DJI GO 4 app and enter the camera view. Tap on the three dots in the right top corner and tap the remote controller icon. Then scroll down and tap “Linking RC”. Credits: Tips 2 Fix. Then select “Primary controller” and hit ok. Credits: Tips 2 Fix.
I carried out the latest firmware update on my Phantom 4 in late January 2020. The firmware installation failed and the camera stopped operating. All was working correctly prior to the update. I tried the DJI Assistant 2 to no avail to repair the issue. I then contacted Ferntech NZ Ltd and sent my P4 to them in early February 2020.
Offline. 5#. According to your OP, you have a DJI Phantom 2 Vision. The black screen cannot be repaired on those. You would have to replace the camera. However, based on the image you provided, the camera is not binded to the range extender which means the FPV may be working just fine although it's not likely.
Open the DJI Assistant 2 and wait until it connects to your DJI Phantom 4. Select DJI Phantom 4 and start the Calibration process. Tap on the button “Start Calibration” that is located on the bottom right side. Place the front side of your Phantom 4 Vision Sensors to look towards the screen. I have a Phantom 2 vision plus and I have had since purchasing it new when the came out. I have not flown it in over a year and now I have pulled it out and I am not getting any wireless signal from the range extender. I have charged everything up, have upgraded the software and firmware all to the latest versions. I have gone thru the rebinding steps for binding range extender to the camera Phantom 3 Professional Firmware v1.4.0010 and IOS 2.3 and worked pretty good. Now the camera went into overheat mode and it's not operational, called DJI and requested RMA. Looks like this camera has limited life. Update this Fourm after its at DJI us and they diagnostic the root cause. Best regards, Steve

Step 1: Connect the Camera to Your Computer. Step 2: Open the Phantom 3 Camera App. Step 3: Select the Mode You Want to Use. Step 4: Click on the Settings Tab. Step 5: Click on Wi-Fi and Connect to the Network. Step 6: Enter the Password and Click on Connect. If you have questions or concerns about using your camera, please contact Dji Customer

mXBaVA.
  • zwk1x552dp.pages.dev/182
  • zwk1x552dp.pages.dev/296
  • zwk1x552dp.pages.dev/114
  • zwk1x552dp.pages.dev/127
  • zwk1x552dp.pages.dev/117
  • zwk1x552dp.pages.dev/70
  • zwk1x552dp.pages.dev/373
  • zwk1x552dp.pages.dev/192

    • dji phantom 2 camera not working